EXACTLY HOW TO INSTALL A BATH TUB: INSTALL AN ACRYLIC TUB AND ALSO TUB SURROUND

Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround

Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround

Blog Article

Schedule A Free Estimate

Do you find yourself in search of know-how about How to Install a Bathtub?


How to Install a Bathtub
Mounting a bathtub isn't exactly rocket science, however it does call for strong plumbing, carpentry, and often, tiling abilities. Changing an old bath tub with a new one is also a moderately tough job. If the old bathtub is conveniently accessible, the project can move quickly; if you have to open a wall surface to eliminate the old bathtub and also place the new bathtub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the work and also fit trying it. As opposed to working with a contractor to take over a halfway-completed task, it is far better to take into consideration using one prior to you start. Opportunities are you might require an expert plumber to make tube links.
This post will assist you install a new bathtub in your bathroom if you have actually currently acquired a brand-new bathtub as well as don't require to alter the plan of your previous supply of water pipes.
Your tools and product list must make up the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Removing Old Touches


    If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water system. After doing so, switch on the taps to drain any kind of water staying in the system. The process of removing the existing faucets can be rather problematic as a result of the limited gain access to that is frequently the case.
    Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipes. Once the supply pipelines have been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
    Before going on to fit the new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

    Fitting New Touches


    If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipelines.
    If you need to fit a monobloc, after that you will call for reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location between the tap and also the sink. Secure the tap in position with the producer supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The former type needs to be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Setting up the Bath tub


    Using the two wood boards under its feet, position the bathtub in the required setting. The wood boards are helpful in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto four tiny factors.
    The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as readjusting the feet on the bath tub till the spirit level reads level.
    To set up faucets, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
    Activate the water supply and check all joints as well as new pipework for leaks as well as tighten them if needed. Load the bath tub as well as additionally examine the overflow electrical outlet and also the normal electrical outlet for leakages.
    Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it into its final setting.

    Preparing for the Installation


    Firstly, the supporting frame provided with the bathroom needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
    Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the provided washers.
    Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final position.

    Tiling Around the Bath tub


    In the area where the bathroom satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall in between the bath as well as the tiling, leading to issues with dampness as well as possible leakages to the ceiling below.
    You can select from a variety of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill the tub with water prior to sealing, to enable the activity experienced when the bathtub is in use. The sealer can fracture fairly early if you do not think about this activity before sealing.
    Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly readily available on the market. It is recommended to fit the tiles utilizing waterproof or water-proof adhesive as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    I have been very eager about Tools You Need to Install a New Bathtub and I really hope you enjoyed the post. In case you enjoyed reading our page please remember to share it. Many thanks for your time invested reading it.




    Or Book Technician Here


    Report this page